Every molder and OEM has the same goal: to optimize production of quality parts and get their products to market on time. There are several strategies out there that will help to accomplish this goal, and many times the molder or OEM looks to his or her mold builder to lay the foundation for a successful project by knowing what is required throughout the mold building process and anticipating what is expected once that mold is built.

Similarly, the mold builder must take the same tack and look to his or her vendors to deliver what is needed on time and on the mark—there is no room for mistakes or long delays. The customer’s expectations behoove the mold builder to think 10 steps ahead on a project and offer viable solutions.
What’s the answer? Find a skilled, knowledgeable mold plating vendor who can help you not only increase protection for your customer’s most valuable asset, the mold, but who can also suggest ways in which a coating can decrease cycle times.

Peak Performance
Many shops have realized the advantages of using nickel-PTFE and nickel-boron-nitride coatings—including increased hardness and better release. For some, the enhanced lubricity also helped to significantly reduce cycle times.
 Of a four-mold project we were awarded, we’ve built two molds that are manufacturing a product from blow molding grade polyethylene. Our biggest issue was that we had to run Saturdays and Sundays, 24 hours, to meet our customer’s high-volume needs.
In addition to the extra hours, they were also encountering problems with sticking. No matter how deep the undercuts were on the B side, the part did not want to release from the A-side, and we couldn’t go any deeper on the undercuts.
So we had a meeting to discuss how to run faster. Because we’d had a lot of experience and success with mold coatings at a previous employer’s shop, we brought up the idea of using plating and Rick said ‘I’m tired of you talking about it. Let’s try it’.
 So we had the first mold plated with the nickel boron nitride,We set up the mold in the machine and the coating made the start-up so much easier. That blow molding grade PE is like concrete to melt. It was taking us an hour to start the machine and now it only takes about 10 minutes. We had no more sticking and right off the bat we cut 5 seconds off the cycle time. After the mold reached ambient temp, we were able to cut another two seconds off the cycle for a more than 25-percent improvement. After plating the second mold, we cut about 8 seconds off that cycle time for a 35-percent cycle time savings.
These significant improvements in cycle times enabled Brandt Industries to stop running the molds on the weekends and still meet its customer’s volume requirements.

Planning and Preparation
Employing the most effective mold plating material begins with appropriate planning and preparation. Early involvement of one’s vendors is critical. Some of the most proactive mold shops have preferred vendor lists and spec books. Within those pages the polishing and plating vendor should be included—and consulted with before that first cavity is machined. With proper documentation about the mold, an effective surface treatment can be put into play with excellent results.
Masking is a key element when plating, and it takes time and is very detailed. It’s an integral part of the success of plating and is also a key step that, when done correctly, makes it possible for the moldmaker to assemble the job with the least amount of secondary work.
Bead blasting is also part of the preparation, and is used to clean the mold’s surface in order to maximize the adhesion of whatever plating process will follow. Highly polished finishes have to be protected during the bead blasting preparation process and also prepared by an experienced polisher prior to plating. These steps are not only important but they save time and money over the course of the plating process.

Additional Strategies
Shops also use different materials like beryllium copper for temperature control and reduced cycle times and production enhancement. It is often asked how a coating would affect the thermal conductivity of a tool. Coatings like nickel-PTFE and nickel boron nitride will not affect thermal conductivity, but will only enhance the protection and release properties of the tool, which in turn can result in reduced cycle times. Talk with your chosen plating vendor up front about every project, including the materials being molded, performance expectations, etc., to ensure the best production outcomes.

About First-rate Mold Solution Co., Ltd.
First-rate Mold Solution Co., Ltd. in China, provide industry design,mold design,mold manufacturing,molding analysis,project management service.

 About www.firstratemold.com
our website has a lot of professional knowledges in mold industry in blog and news, also we are interested in CAD/CAM/CAE, such as AUTOCAD,UGNX, PRO/E,CATIA, CIMATRON, SOLIDWORKS, MOLDFLOW and so on,we welcome professional engineer,mold maker and someone who are interested in injection molding,plastic product,injection mold and mold industry to our section of blog and news,we would like to share with them