In order to be ultra-competitive in this difficult economy, another arrow in the quiver of toolmakers is high-performance copper, which can be employed instead of traditional all-steel tools. The use of high performance copper alloys in mold cores and cavities gives significant advantages over tool steels and aluminum alloys.

  Due to the fact that copper alloys are more expensive than typical mold steel, moldmakers are often hesitant to use these alloys. There are two primary reasons why copper beryllium alloy C17200 and other high performance copper alloys are used in molds which we will discuss: (1) cycle time reduction and capital savings and (2) part quality. This article will also review key mold material properties and the compatibility of glass-filled polymers.

  1. Cycle Time and Capital Savings
For molders whose machines are running at 50-percent capacity—which is not so uncommon in this difficult economy—cycle time reduction is not at the top of their priority list. However, there are times when making a mold with fewer cavities—or making one mold instead of two—is made possible by using high-performance copper alloys.

  There are many examples where the use of copper has allowed molders to produce on four cavities what otherwise would have required an 8-cavity mold. Imagine if you can use one mold instead of two—eliminating the need for an extra molding machine. Now we’re talking about hundreds of thousands of dollars in savings for perhaps a few thousand dollars extra in mold materials.

  Often, molds are built with the least expensive steels because there is a disconnect between the moldmaker, the mold owner and the molder. For example, if a major OEM buys a mold, but the mold is run by a subcontractor, there needs to be very good discussion regarding the price of the mold, the cycle time of the parts and the quality of the parts. If the OEM purchases the tool he may want the cheapest tool possible. The molder then must convince the OEM to spend a little extra in order that the mold will meet the cycle time and part quality requirements, and finally the lowest total cost for the molded parts.

  2. Part Quality
Besides decreasing cycle time, the high thermal conductivity of copper alloys also increases the thermal homogeneity of the part during cooling, which in turn reduces warping. If a tool has poor thermal conductivity, then hot spots can develop during the cooling process. Hot spots are regions where the tooling temperature is higher than the surrounding material and the local cooling rate of the molded part will be lower than that of the rest of the part. This variability in cooling rate can lead to parts warping, yielding inferior and sometimes unusable products.

  There are many examples where a mold is built entirely in steel and the part dimensions and shape are impossible to keep within tolerance. Then, as an afterthought, copper alloys are inserted to solve the problem. Inserting copper after the fact solves the problem, but it is much more cost-effective to design copper into the mold from the very beginning.

  3. Key Mold Material Properties
There are other crucial material properties to consider: strength and hardness. A hard material reduces wear, improving longevity as it reduces the susceptibility of the mold to dents and scratches. However, the material cannot be brittle, so the alloy needs to have both strength and hardness. Therefore, an ideal material for a cavity or core is one that optimizes strength, hardness and conductivity. Aluminum and lower performance copper alloys have high conductivity, but inadequate hardness and strength for many tooling applications.

  There is vast evidence to support that copper beryllium C172 is really the best high-performance copper alloy for molds. No other material is available in the 40 HRc range with thermal conductivity close to CuBe C17200. Other materials have been developed such as CuNiSiCr that are also very good alloys with a maximum hardness of 30 HRc. The size ranges of the CuNiSiCr alloys in the 30 HRc range are very limited—typically up to 5” maximum thickness. Thicker plates are available, but with lower hardness. In addition to thermal conductivity, it is important to also consider material properties such as corrosion resistance, machinability and weldability.

  4. Compatibility with Glass-filled Polymers
Suggest that someone use a copper alloy in a mold for glass-filled polymers and many people will immediately reject the idea. However, glass-filled polymers are molded every day in tools on every continent using C17200 with a hardness of 40Rc. We must remember that in most instances, the polymer is not flowing along the wall of the mold, but is flowing with a fountain flow inside-out pattern—meaning that the velocity of the polymer at the mold surface is zero. We do have to be careful though, in gate areas and where there are sharp corners with thin walls. The mold life can still be very good, but there may be circumstances where weld repair is required or replaceable inserts are recommended.

About First-rate Mold Solution Co., Ltd.
First-rate Mold Solution Co., Ltd. in China, provide industry design,mold design,mold manufacturing,molding analysis,project management service.

 About www.firstratemold.com
our website has a lot of professional knowledges in mold industry in blog and news, also we are interested in CAD/CAM/CAE, such as AUTOCAD,UGNX, PRO/E,CATIA, CIMATRON, SOLIDWORKS, MOLDFLOW and so on,we welcome professional engineer,mold maker and someone who are interested in injection molding,plastic product,injection mold and mold industry to our section of blog and news,we would like to share with them